RMSTATOR
STATOR + CNC MOSFET KIT KAW KRF 800 Teryx 14-21
| In Store |
Not in Store
|
| NZ Warehouse |
Out of Stock
|
DESCRIPTION
Brand new aftermarket stator and red machined aluminium MOSFET regulator kit.
- Direct replacement for the original unit.
- Plug-and-play, direct fit and easy installation.
- All products are tested before shipping.
Product images are accurate. If in doubt, compare the item with the original part to confirm compatibility.
Stator Features:
- High-grade lamination materials.
- High-grade copper windings, resistant to temperatures up to 200°C.
- Pickup/pulser coil included.
- Connector included.
- Rubber grommet included.
Red Machined Aluminium MOSFET Regulator:
The red machined aluminium MOSFET voltage regulator is designed to improve heat dissipation in powersports charging systems. After 10 minutes of use, the billet aluminium heat sink runs up to 33% cooler than standard cast regulator housings. Equipped with MOSFET regulation technology, it is designed for three-phase permanent magnet charging systems.
Stop burning the regulator rectifier! Upgrade to advanced MOSFET technology. It runs cooler than OEM diode-style regulators and features overheat protection. Instead of burning out, the rectifier temporarily switches off to cool down.
- Quality exceeds OEM equipment.
- Improved heat sink and charging capabilities.
- Higher-grade electrical components.
- Runs cooler than traditional shunt voltage regulator rectifiers.
- Reduces stator load, helping reduce engine workload and fuel consumption.
- Provides steadier, smoother battery charging.
- Helps extend battery life and cold-cranking capacity.
- Reduces stator load to help free up engine power.
- Advanced design lowers operating temperatures for improved longevity and performance.
- Optimises power delivery by switching the stator coils on or off.
Opposite connector (main harness side) included. These connectors are commonly affected by melting, corrosion and defects, which can cause recurring electrical problems.
Before Installing the Stator:
- Check the AC output of the stator.
- Replace any burned or corroded connectors on the stator and regulator/rectifier.
- Check and repair any melted wiring.
- Apply high-temperature dielectric grease to all connectors.
The stator may use a different wire colour code from the original. All wires are installed in the correct order. Do not change the wiring configuration. This stator is designed as a direct plug-in replacement.
Always use thread-locking compound when installing the stator. If the stator includes a pickup coil, ensure the air gap is correctly adjusted. Set it as close as possible, but no less than 0.010 inches.
Before Installing the Voltage Regulator:
- Check the AC output of the stator.
- Replace any burned or corroded connectors on the stator and regulator/rectifier.
- Check and repair any melted wiring.
- Apply high-temperature dielectric grease to all connectors.
Warning: Risk of electric shock. Disconnect the battery before servicing. Installation should be carried out by a qualified technician to avoid malfunction.
Stator Dimensions:
- Interior diameter: 42 mm
- Exterior diameter: 105 mm
- Thickness: 20 mm
- Stator-to-grommet wire length: 160 mm
- Grommet-to-plug wire length: 950 mm
- Pickup coil wire-to-grommet length: 90 mm
Other Stator Specifications:
- Number of wires: 5
- Number of plugs: 3
- Number of pins: 5
- Alternator resistance: White wire to white wire: 0.6 ohms ±20%
- Pickup coil resistance: Green wire to blue wire: 500 ohms ±20%
Red Machined Aluminium MOSFET Regulator Dimensions:
- Width: 103 mm
- Length: 103 mm
- Height: 28 mm
- Mounting hole centre-to-centre distance: 80 mm
Other Regulator Specifications:
- Number of plugs: 2
- Number of pins: 5
- Minimum charging voltage: 14.5 V ±0.5 V
- Maximum charging current: 50 A / 500 W
- Open circuit voltage: 15 V
- Operating temperature: -20°C to 85°C
SHIPPING
SHIPPING
Orders can be shipped from either Auckland, Hamilton, Kihikihi, New Plymouth, Wellington or Christchurch warehouses. Depending on the location of items you have ordered, Motozone will ship your purchase from the closest location where possible.
New Zealand
Free shipping on order over $199.00.
For orders under $199.00, shipping throughout New Zealand is $9.99 for Urban and $15.99 for Rural Shipping.
In most cases shipping is overnight however it can take 2-3 days depending on time/day the order was placed. If delivery is to a rural address please allow a couple of extra days. We can ship to your place of work!
Australia
Free shipping on order over $199.00.
For orders under $199.00, shipping throughout Australia is $25.99
Delivery takes approx. 5-10 days delivery.
RETURNS
RETURNS
Any goods purchased from Motozone can be returned within 30 days of receipt for refund or exchange.
The goods must be returned new, unused, unaltered, not previously installed, and in a sellable condition with all of the original packaging.
This right of return will not cover items that are special orders and found to be an incorrect fit, this is the responsibility of the purchaser, however all other standard warranties will apply.
Freight costs will not be refunded.
For the returns process contact or phone Motozone with your invoice number and the reason for return. We will then email you the correct form for processing.