RMSTATOR
STATOR + CNC MOSFET KIT KAW KRF 800 Teryx 14-21
Couldn't load pickup availability
DESCRIPTION
Brand new aftermarket Stator + Red Machined Aluminum Mosfet Regulator Kit
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation
- All products shipped are tested
All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.
Stator
- Highest grade lamination materials
- Highest grade copper windings, resistant to 200 degrees Celsius.
- Pick-up pulsar coil included
- Connector included
- Rubber grommet included
Machined Aluminum Mosfet Regulator
Our new red machined aluminum Mosfet voltage regulator is a great upgrade for heat dissipation in any Powersports charging system. After 10 minutes of use, our billet aluminum heatsink runs cooler by 33% than standard cast regulator housings. Our new red regulator, equipped with the renowned Mosfet regulation technology, is an added value to any three-phase permanent magnet charging system.
STOP BURNING YOUR REGULATOR RECTIFIER!
It is time to update or replace your voltage regulator with the advanced MOSFET type.
It runs cooler than all OEM diode-style regulators. In addition, this rectifier has overheat protection, rather than burn up, it will simply turn off for a while and cool off.
- The quality exceeds the OEM equipment
- Improved heat sink and charging capabilities
- Higher grade of electric components
We have even included the opposite connector (main harness side) as we know these are often melted / corroded/defective and a major cause of repetitive electrical issues.
Dimensions Stator:
Interior diameter: 42 mm
Exterior diameter: 105 mm
Thickness: 20 mm
Length of wires stator to grommet: 160 mm
Length of wires grommet to plug: 950 mm
Length of pickup coil's wire to grommet: 90 mm
Other specifications :
Number of wires: 5
Number of plugs: 3
Number of pins: 5
Wire to wire resistance :
Alternator: White between each White = 0.6 ohms +-20%
Pickup: Green to Blue = 500 ohms +-20%
Dimensions Red Machined Aluminum Mosfet Regulator (CNC) :
Width: 103 mm
Length: 103 mm
Height: 28 mm
Fixation holes center to center: 80 mm
Other specifications:
Number of plugs: 2
Number of pins: 5
Minimum Charging Voltage: 14.5 V +- 0.5 V
Maximum Charging Current: 50 A / 500 W
Open Circuit Voltage: 15 V
Operation Temperature: -20°C to 85°C
SHIPPING
SHIPPING
Orders can be shipped from either Auckland, Hamilton, Kihikihi, New Plymouth, Wellington or Christchurch warehouses. Depending on the location of items you have ordered, Motozone will ship your purchase from the closest location where possible.
New Zealand
Free shipping on order over $149.00.
For orders under $149.00, shipping throughout New Zealand is $7.99 for Urban and $12.99 for Rural Shipping.
In most cases shipping is overnight however it can take 2-3 days depending on time/day the order was placed. If delivery is to a rural address please allow a couple of extra days. We can ship to your place of work!
Australia
Free shipping on order over $149.00.
For orders under $149.00, shipping throughout Australia is $7.99
Delivery takes approx. 5-10 days delivery.
RETURNS
RETURNS
Any goods purchased from Motozone can be returned within 30 days of receipt for refund or exchange.
The goods must be returned new, unused, unaltered, not previously installed, and in a sellable condition with all of the original packaging.
This right of return will not cover items that are special orders and found to be an incorrect fit, this is the responsibility of the purchaser, however all other standard warranties will apply.
Freight costs will not be refunded.
For the returns process contact or phone Motozone with your invoice number and the reason for return. We will then email you the correct form for processing.